Soffit starters are also referred to as wall receivers. There are four popular types of soffit starters available; J-channel, F-channel, reversible F-Channel and Cove Molding. Different starters are typically used for specific scenarios:. For remodeling an existing structure, remove old trim and install a nailing base. If you are adding a new construction to your home, snap a chalk line to the side of the house, level with the fascia board. Position the soffit starter on the underside of soffit framing, and secure using staples or nails.
The staples or nails should be spaced at inch intervals to avoid gapping when securing the soffit panels themselves. Measure the width of the eave where the soffit is needed.
Be sure to measure the full distance between the wall to the front of the fascia board to determine the entire width of the soffit panel needed. This slightly shorter cut will allow for any discrepancies present in the fascia-to-wall distance. Slip the panels into the soffit starter and secure to the bottom of the fascia board using 1-inch aluminum trim nails or staples.
Secure panels at the grooves so that they maintain a smooth appearance that is flush with the fascia board. Continue down the length of the eave. Measure and cut the length of the miter divider. Slip the v-cut end of the miter divider into the soffit starter next to the wall.
Install triangular soffit panels. Be sure that the panel grooves line up with each other along the miter divider for a clean and measured appearance.
Instead, always start the soffit installation in the middle of the length of the overhang. Then, work your way outwards toward each end. This installation strategy helps to create a clean, smooth appearance along the soffit. When installing the fascia above the soffit, the starting point strategy is a little different.
Begin fascia installation at the farthest corner from the front yard, or the farthest corner of the house from the main entrance. Fascia seams tend to be most apparent at their starting point rather than their ending point, so using this technique ensures that the seams are less noticeable along areas of the house that get the most visual attention, like the entryway and front of the house. Aluminum nails sold for soffit and fascia work are soft and short, so it can be frustrating to drive them.
I use a framing nail as a centre punch for getting nail holes started in pieces of soffit, but I never use the standard aluminum nails for securing the aluminum. When expansion and contraction issues are ignored, wavy, buckled fascia is a constant eyesore. It ripples when the sun shines, and smoothens out on cloudy days. Stainless steel nail partially driven into over-sized hole in edge of fascia.
The over-sized hole allows for expansion and contraction of aluminum. Instead of face nailing fascia at the top, tuck it up underneath aluminum drip edge installed around the perimeter of the roof.
This offers plenty of holding power along the top edge, but only when the approach is coupled with nails driven into oversized holes along the bottom edge of the L-shaped fascia profile. The trick here is using corrosion-proof nails that are long enough to extend securely into the solid wood of the roof frame.
Predrill slightly oversized holes aligned with every third groove in the soffit, then hammer the nails home just tightly enough to take up all the slack. In the interests of good looks and weatherproofing, I never face-nail fascia. I always use polyurethane caulking as a glue instead. It comes in colours that match factory finished aluminum, and the long-term holding power of polyurethane is at least as good as nails. Use the glue and tape approach where lengths of fascia meet on long runs, and where fascia ends at the bottom edge of a roof.
As with so many things in the building world, success with soffit and fascia is won in the details. Make allowances for thermal expansion, overlap joints to keep water out, and secure everything firmly against wind. Fascia is a part of your home that everyone will see, so it pays to be particular. Chances are that you've never experienced a properly functioning hand plane. It takes a little effort tweaking and sharpening, but the results are very worthwhile, as you'll see.
Crown molding is a powerful way to improve the look of your home, and here's the place to get tricks and tips for installing crown molding with skill. Looking to learn how to work with wood and don't know where to start? My DIYUniversity Course on woodworking for beginners is the best place online to learn a new skill and develop good working habits that will save you time and energy down the line.
Learn what you need to know to setup your own off-grid energy source with these tried and tested plans. Welding isn't just for the pros, you can learn along with Steve Maxwell everything you need for home workshop welding. Fascia is the vertical edge of a roof, and factory-finished aluminum fascia is an excellent option for this situation. Three main soffit and fascia goals… Preventing water from sneaking behind the aluminum and causing the roof edge to get wet and rot.
Securing fascia so it withstands every kind of harsh weather that comes along.
0コメント