This DIY broadloom carpet is complete with padding attached, saving you money and installation time. Facebook FlooringInc FlooringInc. Over , customers and 40, product reviews. Over Million Sqft of Flooring Covered. Free Samples Samples. Call Us Contact Us. Live Chat. Track Your Order. My Account. Track Order. Categories Monthly Deals Buyer's Guide. Vinyl Flooring Linoleum vs. Engineered Hardwood All Engineered Hardwood. Underlayment All Underlayment. Rubber Flooring Inc. Flooring Inc.
Garage Flooring Inc. Foam Tiles Questions? Call Mon. What DIY project are you interested in? Let the carpet sit for 24 hours in your home. It needs this time to adjust to the temperature and humidity in your home. That's because it may expand or shrink based on these conditions, so you want to make sure it's through with that process before you put it down.
Cut the carpet to size if you don't have space to do it in the room. If your room is small, you may not have enough floor space to bring the carpet in and cut it. Use the measurements you took earlier for the room to cut the carpet to size. Make sure to leave some extra on either end so you don't end up with a piece that's too short.
Roll the carpet out. Start in one corner of the room. Leave 3 to 4 inches 7. Unroll the carpet roll, covering the floor and tack strips as you do. Line up carpet edges as needed to make seams and cover the whole floor. Place seaming tape underneath seams. When you come to a seam, lay seaming tape down on the floor. The sticky part should be facing up. Place the carpet seam over the tape, making sure both edges are covered.
Heat the tape with a seaming iron. Set your seaming iron to 2 or 3. Lift up the carpet on both sides so you can slide the seaming iron underneath the carpet and on top of the tape. Leave it in place for seconds until the adhesive melts, then move it down. Press down on the part of the seam you just heated so the carpet sticks to the tape. Seal the seam with a carpet roller. Run your thumbs over the very center of the seam to make sure it's in place.
Then, use a carpet roller to go over it several times, running it back and forth along the seam. Do this as you heat each section, not at the very end. Wait 20 minutes after doing seams before tacking and stretching it. Keep moving down the seam this way until it's stuck in place.
Tack the carpet into place on one wall with a knee kicker. Place the tooth edge of the knee kicker on the carpet near the wall in a corner. Put it about 3 inches 7. Hit the flat, vertical part sticking out on the other end with your knee, making sure to apply some force. When you hit it, it tacks the carpet on to the strip.
Move along the wall, hitting the knee kicker every 1 foot 0. You will have carpet sticking up over the trim. A knee kicker is a solid metal tool that's about 1. It stretches the carpet over the tack strip. The tacks grab the carpet and hold it firmly in place.
Stretch the carpet across the room and tack it on the other side. Using as much strength as you can, pull the carpet so it's taut across the room.
Use the knee kicker to tack it onto that wall, too. You can use a carpet stretcher for this process, which is a good idea if you have a large room. To use one, place the flat end against the wall you tacked on first, then place the flat part on the floor. It has a lever that gives you leverage and the head pushes the carpet across the floor to stretch it.
Secure the rest of the room with the knee kicker. Tack the other edges of the room with the knee kicker, stretching the carpet as tight as you can while moving around the room.
Remember, you'll have excess carpet on each side that you can trim off in a minute. Part 4. Run a carpet trimming tool along the edge. The carpet tool has a flat metal runner on the bottom, a handle on the top, and a blade on one edge.
Press the tool flat against the carpet and right up against the baseboard on the sharp side. Push it along the wall, applying pressure as you do. Run it underneath the baseboard to cut the carpet. If it starts getting dull, replace the blade. Also, use a box cutter to cut out spaces for your floor vents. Check that you cut cleanly through the carpet before taking the strip off. Look along the edge of the strip you cut off. Make sure no strings are connecting the strip to the main carpet, then pull it up and away from the carpet.
Press the edge of the carpet under the baseboard with a carpet chisel. This tool has a wide, dull blade that lets you press the carpet in place. Use it to wedge the carpet under the baseboard by pressing into the carpet until it settles in place.
Return any hardware you removed. If you took doors off, put them back in place. Put the door stops back. If you took up floor vents, screw them back in place. Move your furniture and belongings back in place, and you're done! You can, but it will be very difficult to get the carpet taut and properly fitted to the floor.
Your finished carpet may have bumps, bulges, and wrinkles. To install the carpet without a stretcher or knee kicker, put on some shoes with good treads and stretch the carpet toward the walls by jumping on it and driving forward with your feet.
Not Helpful 0 Helpful 3. The job also requires some more common tools, such as a hammer, measuring tape, hand stapler, and various cutting tools. Not Helpful 0 Helpful 0. James Steve Fair. This will save you time, money, and effort. You will experience more waste with patterned carpet than with non-patterned carpet, since cutting and seaming pieces requires you to match the pattern.
Most experts recommend adding 5 percent overage for waste on a non-patterned carpet, and you should add another 5 percent, for a total of 10 percent overage, for patterned carpeting. The larger the pattern, the more waste you will have.
This is a standard rule of carpet installation: Do not lay the padding over the tackless strips. Keep the padding within the inner perimeter formed by the strips. Padding should touch the edge of the tackless strips but should not overlap them. It is also a good idea to make sure your padding is of very good quality. Even cheap carpeting will perform much better if the underlying padding is of good quality, such as high-density memory foam.
Obviously, if your carpet has a pattern, seaming two pieces requires careful attention to matching the pattern between adjoining pieces. Keep carpet pile consistent from piece to piece. Even professional installation teams have been known to get this wrong. Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile.
Measure ad performance. Select basic ads. Create a personalised ads profile.
0コメント